DIY ZVS Tesla Coil Power Supply Boost Voltage Generator Drive Board

Specification: Size: 74mm * 77mm Input voltage: DC 12-30V Output: HVDCÂ£Â¬ About 800 times of input voltage Power requirements: Less than 12V ≥ 5AÂ£Â¬ above 15V ≥ 15A Operating frequency: 30kHz~50kHz adaptive Secondary parameters: 5T + 5T Feature: 1. Using military FR4-A material 1.6mm double-board circuit boardÂ£Â¬ power line extra add tin and optimizes line width of MOS tube drive circuit! 2. Using two IRFP250N power field pipeÂ£Â¬ large currentÂ£Â¬ small internal resistanceÂ£Â¬ super-power! 3. Using 1.25 copper wire large inductanceÂ£Â¬ more stable performance. 4. Using 1% precision metal film resistors! 5. Use 25 * 24 * 16mm thick anti-static cooling! 6. Using MKP 0.33UF 1200V two parallel resonant capacitor for high frequency. Precautions: 1. After finish the installationÂ£Â¬ carefully check it and verify that all components soldered correctly 2. Please note that the positive and negative signs of input powerÂ£Â¬ carefully check to prevent reverse burning plate 3. The test voltage is recommended for the low power 12VÂ£Â¬ prevent mis-wiring problems or cause burning plate 4. Drive board limit input is DC 30VÂ£Â¬ current 10AÂ£Â¬ not recommended using limitsÂ£Â¬ do not long working under overvoltage and over-current conditions. Driver board is not suitable for induction heatingÂ£Â¬ if you need induction heatingÂ£Â¬ it is recommended input voltage 15V or less. For induction heating or long use high-power must need to add the cooling fanÂ£Â¬ if poor heat dissipationÂ£Â¬ it will result in MOS tube temperature is too highÂ£Â¬ will accelerate the aging of MOS tube even burn and other issues.

Click here to buy now - $13.78

DIY ZVS Tesla Coil Power Supply Boost Voltage Generator Drive Board

Specification: Size: 74mm * 77mm Input voltage: DC ~-30V Output: HVDCÂ£Â¬ About 800 times of input voltage Power requirements: Less than 12V ≥ 5AÂ£Â¬ above 15V ≥ 15A Operating frequency: 30kHz~50kHz adaptive Secondary parameters: 5T + 5T Feature: 1. Using military FR4-A material 1.6mm double-board circuit boardÂ£Â¬ power line extra add tin and optimizes line width of MOS tube drive circuit! 2. Using two IRFP250N power field pipeÂ£Â¬ large currentÂ£Â¬ small internal resistanceÂ£Â¬ super-power! 3. Using 1.25 copper wire large inductanceÂ£Â¬ more stable performance. 4. Using 1% precision metal film resistors! 5. Use 25 * 24 * 16mm thick anti-static cooling! 6. Using MKP 0.33UF 1200V two parallel resonant capacitor for high frequency. Precautions: 1. After finish the installationÂ£Â¬ carefully check it and verify that all components soldered correctly 2. Please note that the positive and negative signs of input powerÂ£Â¬ carefully check to prevent reverse burning plate 3. The test voltage is recommended for the low power 12VÂ£Â¬ prevent mis-wiring problems or cause burning plate 4. Drive board limit input is DC 30VÂ£Â¬ current 10AÂ£Â¬ not recommended using limitsÂ£Â¬ do not long working under overvoltage and overcurrent conditions. Driver board is not suitable for induction heatingÂ£Â¬ if you need induction heatingÂ£Â¬ it is recommended input voltage 15Vv or less. For induction heating or long use high-power must need to add the cooling fanÂ£Â¬ if poor heat dissipationÂ£Â¬ it will result in MOS tube temperature is too highÂ£Â¬ will accelerate the aging of MOS tube even burn and other issues. Note: This is a DIY kitÂ£Â¬ you need to have electronic knowledge and ability.

Click here to buy now - $12.46