Trigger Cycle Timer Delay Switch Circuit Dual MOS Tube Control Board

0.1 seconds (minimum) to 999 minutes (maximum) continuously adjustable This product is easy to useÂ£Â¬ powerfulÂ£Â¬ but all buyers a detailed look at the product instructionsÂ£Â¬ very useful product. Features and application: 1. To achieve a high-frequency circuit fast frequent on-off switch unlimited number of times; 2. The on-off process does not produce noiseÂ£Â¬ no sparkÂ£Â¬ no electromagnetic interference; 3. life long life than conventional electromagnetic relay; 4. Dual MOS shunt active outputÂ£Â¬ lower resistanceÂ£Â¬ more currentÂ£Â¬ strong powerÂ£Â¬ 15AÂ£Â¬ 400WÂ£Â¬ to meet the most use of the equipment; 5. often used to control motorsÂ£Â¬ light bulbsÂ£Â¬ LED lightsÂ£Â¬ DC motorsÂ£Â¬ micro-pumpsÂ£Â¬ solenoid valvesÂ£Â¬ etc.Â£Â¬ through this moduleÂ£Â¬ you can easily control these devicesÂ£Â¬ very convenient. Module Highlights: 1. Wide voltage (5 ~ 36V)Â£Â¬ most devices can be usedÂ£Â¬ very convenient; 2. The interface is clear and simpleÂ£Â¬ powerfulÂ£Â¬ easy to understandÂ£Â¬ meet almost all your needs; 3. There is a key stop function (STOP key)Â£Â¬ with reverse polarity protectionÂ£Â¬ reverse polarity does not burn; 4. Add the sleep mode functionÂ£Â¬ after enablingÂ£Â¬ without any operation within 5 minutesÂ£Â¬ turn off the monitor automatically; Any key to wake up; 5. You can set a different OPÂ£Â¬ CLÂ£Â¬ LOP parametersÂ£Â¬ which are independent of each otherÂ£Â¬ were saved; 6. When all settings automatic power-down save parameters. Operating mode: P1 mode: after the trigger signalÂ£Â¬ the relay is turned OP timeÂ£Â¬ and then disconnect; in the OP timeÂ£Â¬ as follows P1.1: Invalid signal triggered again P1.2: Re-timing signal is triggered again P1.3: Reset signal is triggered againÂ£Â¬ the relay offÂ£Â¬ stop counting; P-2: to the trigger signalÂ£Â¬ relay off for time CLÂ£Â¬ OP relay conduction timeÂ£Â¬ after the counting is finishedÂ£Â¬ disconnect relay; P3.1: After the trigger signal to the relay turned OP timeÂ£Â¬ relay off CL timeÂ£Â¬ then the operation cycleÂ£Â¬ to signal to the relay offÂ£Â¬ stop the counting once again within the loop; cycles (LOP) can be set; P3.2: After power without triggering signalÂ£Â¬ the relay is turned OP timeÂ£Â¬ relay off CL timeÂ£Â¬ cycle the operation; cycles (LOP) can be set; P-4: signal holding function if there is a trigger signalÂ£Â¬ timing is clearedÂ£Â¬ the relay remains on; when the signal disappearsÂ£Â¬ after timing OP disconnect relay; timer periodÂ£Â¬ then there is a signalÂ£Â¬ the timing is cleared; Product parameters: 1: Operating Voltage: DC 5V - 36V; 2: The trigger source: high trigger (DC 3.0V-24V) signal with no common ground system to improve anti-jamming capability of the system (also self-shorting common ground) 3: output capacity: DC 5V - 36VÂ£Â¬ at room temperatureÂ£Â¬ continuous current 15AÂ£Â¬ power 400W! Lower auxiliary cooling conditionsÂ£Â¬ the maximum current up to 30A. 4: Quiescent Current: 15mA 5: Availability: unlimited switch; Operating temperature: -40-85 Â¡Ã¦; 6: with optocoupler isolationÂ£Â¬ enhanced anti-jamming capabilityÂ£Â¬ industrial grade circuit boardsÂ£Â¬ set the parameters after power failure memory forever. pay attention: Module is active charging outputÂ£Â¬ the output side (load side) a voltage equal to the input terminal voltage (DC 5V - 36V). 'DC +' load '+' polarization itself is internally shortedÂ£Â¬ but 'DC-' load '-' in the course of the poles can not be shortedÂ£Â¬ otherwise the load can not be controlled on and offÂ£Â¬ the load is equivalent to It has been carrying electricity. Timing range 0.1 seconds (minimum) to 999 minutes (maximum) continuously adjustable How to choose the time range: After setting the parameter values in the mode selection screen by a short press STOP buttonÂ£Â¬ select the time range; XXX decimal point bitsÂ£Â¬ timing range: 1 second to 999 seconds XX.X decimal point in tenÂ£Â¬ Timing range: 0.1 seconds to 99.9 seconds X.X.X. decimal full brightnessÂ£Â¬ Timing range: 1 minute to 999 minutes For exampleÂ£Â¬ you want to set up OP is 3.2 secondsÂ£Â¬ then move the decimal point to tenÂ£Â¬ the digital display 03.2 Parameter Description: OP-timeÂ£Â¬ CL off timeÂ£Â¬ LOP cycles (1-999 timesÂ£Â¬ "---" represents infinite loop) These parameters are independent of each otherÂ£Â¬ but each of these common mode parametersÂ£Â¬ for exampleÂ£Â¬ P1.1 set OP-time is 5 secondsÂ£Â¬ the user wants to switch to P1.2 modeÂ£Â¬ then enter P1.2 set the appropriate parametersÂ£Â¬ OP It will be five seconds; In the main interface (display 000) Press SET button will display OP (CLÂ£Â¬ LOP) and the corresponding time XXX; If only OP mode (such as the mode P1.1Â£Â¬ P1.2Â£Â¬ P1.3) timeÂ£Â¬ then press SET button will display only the OP and the corresponding time; If the pattern has OPÂ£Â¬ CLÂ£Â¬ LOP (such as the mode P3.1Â£Â¬ P3.2) then press the SET button OP and the corresponding timeÂ£Â¬ CL and the corresponding timeÂ£Â¬ LOP and the corresponding number will be displayed; In the set modeÂ£Â¬ the main interface parameters by a short press the SET button can easily see the current mode set inÂ£Â¬ very convenient! How to set parameters 1. FirstÂ£Â¬ determine the operating mode of the relay; 2. The mode of operation of the relayÂ£Â¬ in the main interface (when the module is powered onÂ£Â¬ flashes the current work mode (P1.1 default mode)Â£Â¬ then enter the main interface) "long press SET button for 2 seconds after the release "to enter mode selection screen by press UPÂ£Â¬ DOWN buttons to select the mode to be set (P1.1 ~ P-4); 3. After selecting the mode to be set (for exampleÂ£Â¬ P3.2) Press SET key to set the appropriate parametersÂ£Â¬ then the parameter to be set flashes (OP-timeÂ£Â¬ CL off timeÂ£Â¬ LOP cycles ( "- - "represents infinite loop)) by UPÂ£Â¬ DOWN to adjust the valueÂ£Â¬ support long press (rapid increase or decrease) and press (increase or decrease one unit); setting the parameter value by a short press STOP button to select the decimal point positionÂ£Â¬ select time range (corresponding time of 0.1 seconds to 999 minutes); short press sET key to set the next parameter of the current modeÂ£Â¬ the process above; 4. After setting the parameters of the selected mode is goodÂ£Â¬ press the SET button for 2 seconds after releaseÂ£Â¬ currently set mode will flashÂ£Â¬ and then return to the main screenÂ£Â¬ set the parameters of success is very simple! The main interface: In the relay does not work status display "000" (no decimal point)Â£Â¬ with a decimal point under relay stateÂ£Â¬ very clear! Mode selection screen: Long press SET to enterÂ£Â¬ after setting is completedÂ£Â¬ press SET key to exit and return to the main interface is very simple! STOP button extensions: Relays enable mode: 1. ON: inner OP-time relay allows conduction; 2. OFF: relay prohibit conduction is always closed; In the main interfaceÂ£Â¬ short press the STOP button to switch between ON and OFFÂ£Â¬ the current in which the state will flashÂ£Â¬ and then return to the main screen. (This feature is an emergency stop functionÂ£Â¬ a key disconnect relay closed) Sleep mode: 1. C-P Sleep mode: five minutes without any operationÂ£Â¬ the digital display automatically turns offÂ£Â¬ the normal operation of the program; 2. O-d normal mode: digital display always open; Press STOP button for two secondsÂ£Â¬ to switch C-P and O-d stateÂ£Â¬ in which the current state of flashes and then return to the main screen.

Click here to buy now - $7.99